Guilin Hengda Mining Machinery

Raymond Mill   is a commonly industrial milling equipment.  It  is applied to the non-flammable and explosive mining building materials, chemical, metallurgical and other industries more than 280 kinds of materials with Mohs hardness under 6 and water content less than 6%, such as  barite, calcite, potash feldspar, talc, marble, limestone, ceramics, glass etc. Here are the factors affecting the production efficiency of Raymond mill . 1 .   T he hardness of the material : the harder material is, the more difficult to grind and the more serious the wear and tear on the equipment. The speed of r aymond mill is slow, of course  the capacity is low . It is recommended that customers use the Raymond Mill strictly  according to the instructions. Do not use this equipment to grind  the hard materials outside the equipment capacity. 2.  Humidity of the material : When the moisture contained in the material is large, the material is ea...

Due to the different types of   raymond  mill  processing capabilities and the presence of wear in the production, the equipment is very strict in the nature of the materials required for material handling. One of them is the moisture content of the material. The following analysis of the material moisture content. 1. Low  moisture content In this case, it ’ s easy to grind the material for the raymond mill . Due to the small moisture content, it ’ s n ot easy to plug  and easy to sieve .   So t he production process is relatively smooth  and  the efficiency of the mill is h igh, this is a better situation and is conducive to the production. 2. High moisture content When the moisture content is high , the ground  material tends to adhere to the grinding roll ring and the liner. This time, the performance of these parts will be reduced and the production efficiency will be reduced. This will also cause the phenomenon of increa...

The continuous development of the times requires continuous development and continuous improvement of the   raymond mill , and it must be recognized by the market. In general, there are four aspects of raymond mill development,  quality improvement, structural improvement, and environmental protection  n eeds and   intelligen t improvements. 1 .   Q uality improvement Because the quality of the mill's production process, not only affects the efficiency of production, but also affect the maintenance costs of investment, then in order to get good production efficiency, we need to continue to improve the quality, if the quality can not meet the production needs , then it will not get the customer's approval, this milling equipment is also difficult to obtain good development . 2.  S tructural improvement In the development of the mill, the performance requirements of the production process are getting higher and higher,  the structu...

Raymond Mill   is a commonly used grinding equipment, mainly used for thermal insulation materials of barite, calcite, talc, marble, limestone, dolomite, fluorite, lime, petroleum coke and other chemical raw materials, Mohs hardness of 6-9, humidity less than 6% of non-inflammable and explosive minerals, chemicals, construction and other industries more than 280 kinds of high-preparation materials processing. Raymond grinding mill with many kinds of wear parts , one of which is the spindle,  when the spindle  is used, one of the faults is the phenomenon of deformation, what ’ s the reason? 1、 T he phenomenon of excessive feed particle size, due to different types of Raymond Mill can handle the size of the material size is limited, if the feed size is too large, it will increase the difficulty of production, and due to feed will Direct contact with the spindle, so if the feed size is large, it will cause the number of collisions with the spindle increases, causin...

The grinding mill  is the main equipment for grinding materials. It can process the materials into finer powders for use in industries such as cement, cosmetics, chemicals etc. Since the machine has different types, these different types can fulfill different requirements. The prices of the mills are not the same, but the prices of the mills on the market is not stable, sometime is high but sometimes is low . What causes this phenomenon? In general, the overall change trend of the price of mills in the market is mainly related to the level of prices, market competition, and policy orientation. Here are the detailed analysis of these three factors: First, the price level When the milling machine is manufactured, it requires human and material resources. No matter if it is human or material, it requires capital investment. When the price is high, whether it is the required human resources or the production material required is more expensive, so the The cost of the ...

In recent years, with the continuous expansion of environmental protection, China has made clear regulations and requirements for the utilization of industrial waste slag. As a result, more and more companies are gradually paying attention to slag, water slag, steel slag, fly ash, etc  i ndustrial waste residue follow-up problem. As a by-product of blast furnace ironmaking, people have gained a deeper understanding of blast furnace slag in recent years. In terms of application, blast furnace slag has the following advantages: 1. Improve the workability of concrete The slag powder needs a small amount of water, and after mixing, the water-cement ratio of the concrete can be reduced, and the amount of concrete bleeding can be reduced, thereby increasing its fluidity, workability, and pumpability so as to maintain its good workability. 2. Reduce the heat of hydration of concrete Because part of the cement can be replaced by equal amounts, the exotherm during the...

Raymond Mill  fan structure is an important part of the equipment, for this part of the structure design to effectively avoid fan vibration. In the actual production, if we encounter such problems, we must adopt a professional way to adjust to achieve reasonable maintenance of the equipment. Raymond Mill's complete structure is composed of main engine, analyzer (powder separator), pipeline device, blower, finished cyclone separator, jaw crusher, bucket elevator, electromagnetic vibrating feeder, electronically controlled motor etc. And these parts are all important components of Raymond Mill. Which of these parts will affect the stability of Raymond Mill's work flow and bring economic losses. This is something that every customer does not want to see, so i t is very important that the daily maintenance of the powder mill accessories. Guilin Hengda made a summary of the reasons for Raymond Mill fan vibration: (1)  When the milling machine is working, the main mac...

Recently, many customers consulted about the manufacturing accuracy of the grinding ring, the lubrication of the grader, the positive pressure of the roller, and other parameters. Today Guilin Hengda briefly introduces several main parameters commonly used in ultrafine grinding mill , hoping to solve y our question. (1) Manufacturing precision of ultrafine grinding ring As the ultrafine mill works, the grinding ring that rotates with the main shaft is one of the main wearing parts, so the manufacturing accuracy of the grinding ring directly affects the service life of the grinding ring. The key is to control the radial runout and grinding ring of the grinding ring. The heat treatment deformation, radial runout and internal diameter deformation will increase the impact on the roller, vibration, increase the additional load, thereby shortening the life of the grinding roller and grinding ring. (2) The positive pressure of the ultr a fine grinding mill  roller and the...

Guilin Hengda   h as  summarized the various failures that Raymond Mill  has encountered during its use  according to the comprehensive R&D production experience and customer feedback, and provides related solutions  for your reference: Common faults  1 : No powder or low yield. R reasons: (1) The powder locker is not adjusted properly and the seal is not good , resulting in powder sucking. (2) B lade wear  terribly , material can not afford shovel. Solution s : (1) Check and adjust the lock of the powder locker. (2) Replace the blade. Common fault 2 : The finished powder is too thick or too fine. R eason s : (1) The blades of the analyzer are seriously worn and do not have grading effects. (2) The air volume of the fan is not appropriate. Solution s : (1) Replace the blades, and properly turn down  the air intake of the fan to solve the rough. (2) Too fine should increase the imported air volume. Common fau...

Ultrafine grinding mill   is mainly applied to the grinding of metallurgy, building materials, chemical industry, mines and other mineral products, quartz, feldspar,    clay, bentonite, calcite, talc, barite, fluor ite ,   white mud, gypsum etc non-flammable and explosive materials with a hardness equal to or less than 6  in Mohs and less than 6% in humidity. U ltrafine  mill  is mainly composed of electric motor, feed outlet, fan, analysis machine, air duct, pulse dust collector etc. The fan is mainly used to provide air flow, so that the material after grinding can be smoothly entered  and selected. However, improper use of staff in daily operations may cause the machine not work . Today, Guilin Hengda  simply analyzes the reasons for the failure of the fan and the corresponding solutions. First of all, when the main shaft of the fan and the motor shaft  doesn ’ t at the same position  , there will be a case where...

In today's increasingly scarce oil resources era, petroleum coke can be used as a substitute for petroleum as a fuel after being ground into a petroleum coke powder, and is widely used in the glass and ceramic industries. So what exactly is petroleum coke? Petroleum coke is the most “scrap” in the oil refining process. From the appearance, it is an irregularly shaped, black block or granule of different sizes. It is further processed into a petroleum coke powder f uel  by grinding mill , which  is a good material for realizing waste utilization and developing a recycling economy. 1. Classification and properties of petroleum coke Needle coke : With a pronounced needle-like structure and fiber texture, it is mainly used as a high-power and ultra-high-power graphite electrode in steel - making. Sponge coke : high chemical reactivity, low impurity content, mainly used in aluminum industry and carbon industry. Projectile coke  (spherical coke): spherica...

Raymond Mill's main machine is divided into three parts, the bottom spiral inlet, the middle of the cylinder grinding chamber, the top of the analyzer. The Raymond Mill produces vibrations for the following reasons: First , the impact of the grinding roller on the grinding ring; the feeding should be uniform, and the empty load operation should be avoided as much as possible. Second , the host part may not be tightly fixed, and the anchor bolts are loosened; check whether each connection is fixed in place before working. Third , Raymond Mill main bearing gap is large, resulting in plum swing; Forth , the analysis of the blade imbalance; See if the blade is complete, some manufacturers in order to save time and save costs, the blade is not debugging to install. Fifth , the installation is uneven; in the installation process, with the spirit level correction   as much as possible  Sixth ,  The material in the volute is clogged; some mate...

In the process of using the pulverizer, it is difficult to avoid problems, which affecting the quality of the finished product and the progress of the work. How to solve  these problems, the standard operation and routine maintenance of the mill are particularly important. Guilin Hengda is a professional grinding mill manufacturer , today brings you the standard operation and daily maintenance of the mill, hoping to solve your confusion. (1) Operate the mill in strict accordance with the requirements of milling. First adjust the large rolling distance and then turn on  the machine. After the material enters, adjust the rolling distance to normal. (2) The power of the pulverizer is large, and the power can be doubled with the change of the rolling distance. Therefore, the tightness of the belt needs to be paid more attention. (3) Before turning on the machine, remove the debris inside and around the machine. Turn the parts by hand to check the degree of...

(1) Increase the number of impeller blades Because the more blades there are, the probability of impact on the fly ash particles passing through the blades per revolution of the impeller is higher and the centrifugal force field generated is greater. The thickness of the blade should be chosen as thin as possible because the thinner the blade, the smaller the resistance to dust gas passing through the impeller. Of course, the determination of the parameters must also consider the impeller's rigidity, strength, and wear resistance. Excessively dense blades will increase the pressure loss and power consumption of the grading machine, as well as affect the normal grading. (2) Reasonable classifier casing design This is related to the shape of the classification room and the area. If the classifying chamber is too small, the fly ash powder will reflect randomly in the classifying chamber, making the turbulence very turbulent and affecting the normal classification. I...